Fresh, brackish and marine fishkeeping with Graham Reed, The Tank Whisperer. 30+ years of wet sleeves.

Water Changes: How Often and How Much

The short answer: change 25 to 30% of the water every week, using dechlorinated tap water at the same temperature as the tank. Clean the gravel with a siphon as you go. It’s the single most useful job in fishkeeping, and it takes about 20 minutes.

Why change water at all?

Your filter turns toxic ammonia into nitrate, but nothing in a normal tank removes nitrate. It builds up week after week, along with hormones, dissolved waste and lost minerals. Fresh water dilutes the bad stuff and puts back the good. It’s also how you keep pH steady, because tap water tops up the KH that stops pH crashing. See aquarium water parameters.

How much and how often

TankHow muchHow often
Typical community tank25 to 30%Weekly
Lightly stocked, heavily planted20 to 25%Every 1 to 2 weeks
Heavily stocked, goldfish, big cichlids40 to 50%Weekly, or 2 × 25%
Nano tank under 30 litres20 to 25%Weekly; small tanks swing faster
Marine fish-only10 to 20%Every 1 to 2 weeks
Reef10%Weekly
Fish-in cycle or ammonia reading25 to 50%Whenever ammonia or nitrite is above 0.25 ppm

Let nitrate be your guide. If it stays under 20 to 40 ppm between changes, your routine is right. If it creeps up, change more or more often.

Kit you need

  • A gravel siphon (gravel vac) with a long hose
  • A bucket used only for the aquarium, never for household cleaning
  • Dechlorinator (water conditioner) that handles chloramine
  • A thermometer
  • An algae scraper or magnet, and an old towel
  • Optional: a hose that connects to the tap (Python-style) for bigger tanks

Step by step

  1. Switch off the heater (and the filter, if the water level will drop below its intake). A heater out of water can crack.
  2. Scrape the glass first, so the loose algae gets siphoned out.
  3. Siphon the gravel. Push the vac into the gravel, let the dirt lift, then move on. Do a third to half of the gravel each week, not all of it. On sand, hover just above the surface.
  4. Stop at your target. Mark 25% on the bucket or the tank so you know where to stop.
  5. Prepare new water. Match the temperature within 1 to 2 °C by feel and by thermometer. Add dechlorinator for the whole tank volume if you’re filling straight from a hose; for the bucket volume if using buckets.
  6. Refill gently. Pour onto a rock or your hand, so you don’t blast the substrate.
  7. Switch everything back on and check the heater light and filter flow before you walk away.

Rinse filter sponges in the old tank water you’ve just taken out, not under the tap, and only when flow drops. More in how to clean your filter.

Common mistakes

  • Forgetting the dechlorinator. Chlorine and chloramine kill fish and filter bacteria. Every time, every bucket.
  • Cold water. A big change with cold water shocks fish and can trigger whitespot.
  • Huge changes after months of none. If you’ve fallen behind, the tank’s water has drifted a long way from tap water. Get back on track with 20% every couple of days, not one 80% change.
  • Cleaning everything at once. Gravel, filter and decor all on the same day strips out too many bacteria. Stagger them.
  • Using hot-tap water. It can carry metals from the tank and pipes. Mix cold tap water with a kettle, or use a heater in the bucket.
  • Softened water. Water from a domestic softener is loaded with sodium. Use the drinking-water tap.
  • Just topping up. Topping up evaporation isn’t a water change. Evaporation removes pure water and leaves the waste behind.

Marine water changes

Mix new salt water with RO water a day ahead, with a heater and a pump in the mixing bucket, and check the salinity matches the tank (1.025 to 1.026 SG). Never add dry salt straight into the tank. Top up evaporation with fresh RO water only. More in marine for freshwater keepers.

Your questions, answered

Do I need to take the fish out? No. Leave them in. Taking them out stresses them far more than a water change.

Can I do a water change in a brand-new tank? During a fishless cycle, only at the end (a big one to bring nitrate down). During a fish-in cycle, yes, as often as the readings need.

Can I leave tap water to stand instead of using conditioner? Not safely. Most UK water uses chloramine, which doesn’t gas off. Use dechlorinator.

Will a water change kill my good bacteria? No. They live in the filter and on surfaces, not in the water. See the nitrogen cycle.

My fish act oddly after a water change. Why? Usually temperature, missing dechlorinator, or a big pH difference between tank and tap. Test the tank and the tap, and do smaller, more frequent changes until they match.

Next reads: Water parameters · The nitrogen cycle · Aquarium algae · Start here

Not sure your routine is right? Tell me your tank size, stocking and nitrate reading in the comments. — Graham

Get in touch I’d love to hear from you

This site uses Akismet to reduce spam. Learn how your comment data is processed.